How to Build Your Own Coils for a Refillable Vapes

Building your own coils for a Refillable Vapes device, also known as coil building, is a popular practice among vaping enthusiasts. It allows you to customize your vaping experience by creating coils tailored to your preferences in terms of resistance, wire type, coil diameter, and coil configuration. Here’s a step-by-step guide on how to build your own coils for a refillable vapes:

1. Gather Your Supplies:

  • Wire: Choose a suitable wire type for your coils, such as Kanthal, stainless steel, nickel, or nichrome. Each wire type has different properties and is suitable for different vaping styles.
  • Coil Jig or Rod: A coil jig or rod helps you wrap your wire into uniform coils of the desired diameter.
  • Wire Cutters: Use wire cutters to trim the excess wire after wrapping your coils.
  • Tweezers: Tweezers are handy for adjusting the coil shape and positioning.
  • Ohm Reader: An ohm reader allows you to measure the resistance of your coils to ensure they are within a safe range for your device.
  • Scissors or Clippers: Use scissors or clippers to trim the wire to the desired length.
  • Cotton: Organic cotton pads or cotton strips are commonly used as wicking material for coils.
  • Ceramic Tweezers (Optional): Ceramic tweezers are heat-resistant and can be used to compress and shape the coils while dry firing.

2. Determine Coil Specifications:

  • Before building your coils, decide on the specifications such as coil resistance, coil diameter, and coil type (e.g., single coil, dual coil, etc.). Refer to online coil calculators or Ohm’s law calculations to determine the number of wraps and wire gauge needed to achieve your desired resistance.

3. Wrap Your Coils:

  • Use a coil jig or rod to wrap the wire around it, ensuring each wrap is tight and evenly spaced. The number of wraps will depend on the desired resistance and wire gauge. Make sure to leave enough excess wire on each end to attach the coil to your atomizer.
  • Once wrapped, gently squeeze the coils together with tweezers to remove any gaps and ensure uniform heating.

4. Install and Position Your Coils:

  • Insert the coils into the posts of your atomizer, making sure they are positioned evenly and aligned with the airflow. Secure the coil leads by tightening the post screws with a screwdriver.
  • Use wire cutters to trim the excess wire leads, leaving just enough to ensure a secure connection without touching the atomizer’s deck or other coils.

5. Check Coil Resistance:

  • Use an ohm reader to measure the resistance of your coils. Ensure that the resistance matches your intended target resistance and falls within the safe operating range of your device.

6. Dry Fire and Adjust:

  • Attach your atomizer to your device and pulse fire the coils at a low wattage to check for hot spots and uneven heating. Use ceramic tweezers to gently compress and adjust the coils while dry firing until they heat up evenly from the center out.
  • Once the coils are heating evenly, let them cool down and re-check the resistance to ensure it hasn’t changed significantly.

7. Wick Your Coils:

  • Cut a strip of organic cotton and thread it through the center of each coil, ensuring the cotton makes full contact with the coil and isn’t too tight or too loose. Trim any excess cotton on the ends to fit into the wicking channels of your atomizer.

8. Prime Your Coils and Vape:

  • Prime your coils by saturating the cotton with e-liquid and allowing it to absorb for a few minutes. Reassemble your atomizer, fill the tank with e-liquid, and you’re ready to vape with your freshly built coils.

9. Monitor and Maintain Your Coils:

  • Monitor the condition of your coils regularly and replace them as needed to ensure optimal performance and flavor. Keep your coils clean by dry burning and rinsing them under running water periodically to remove any residue buildup.

By following these steps, you can build your own coils for a Refillable Vapes device and customize your vaping experience to suit your preferences. Coil building requires practice and patience, so don’t be discouraged if your first attempts aren’t perfect. With time and experience, you’ll be able to master the art of coil building and enjoy the satisfaction of vaping on coils you’ve built yourself.

Leave a Reply

Your email address will not be published. Required fields are marked *